Version: Date: Friday, November 23, 2018 11:19:00 AM CM Server

CST – Computer Simulation Technology

Microstrip – Quarter-wave Transformer

E-field phase animation at 1 GHz" title="E-field phase animation at 1 GHz

The Physics

A quarter-wave transformer is a simple impedance transformer which is commonly used in impedance matching in order to minimize the energy which is reflected when a transmission line is connected to a load. The quarter-wave transformer uses a transmission line with different characteristic impedance and with a length of one-quarter of the guided-wavelength to match a line to a load.
A basic schematic is shown in Fig. 1.

Circuit schematic of a quarter-wave transformer.

Figure 1: Circuit schematic of a quarter-wave transformer


From the literature [1] we write the equation that determines the value of the impedance Z1


From this impedance, the width of the microstrip can be calculated by a more complex equation [1].

The guided wavelength λ is shorter than the free-space wavelength due to the presence of the dielectric substrate. The equation for guided wavelength is also given in [1].

The Model

The quarter-wave transformer in this example connects a 50 Ω line to a 100 Ω load at 1 GHz, and is realized using a microstrip technology on an FR-4 substrate and modeled in CST STUDIO SUITE® as shown in Fig 2.

Quarter-wave transformer in microstrip modeled in CST STUDIO SUITE ®

Figure 3: Quarter-wave transformer using microstrip technology modeled in CST STUDIO SUITE.


This model has a microstrip of  50 Ω that needs to be matched to a load of 100 Ω. By using Eq. 1 we find that the transforming line has 70.71 Ω. The microstrips must be realized on a substrate with εr=4.3, a thickness of 1.2 mm and a metallization of 0.035 mm. In Table 1 we summarize all the parameters of this project.

Parameter Value Description
h 1.2 mm Substrate thickness
t 0.035 mm Metallization thickness
eps r 4.3 Substrate permittivity
Z0 50 Ω System characteristic impedance
RL 100 Ω Load impedance
W50 2.35 mm 50 Ω line width
W70 1.23 mm 70.71 Ω line width
I70 41.84 mm Transformer length

Model Construction Watch Video

Download Model File (Student Edition) Download Model File

Discussion of Results

E-field phase animation at 1 GHz

Figure 3: E-field phase animation of a quarter-wave transformer showing no reflection in the load.


Fig. 3 shows the E-field phase animation. On that animation we can see that at the resonant operating frequency (1 GHz) there is no reflection from the load, and therefore the load of 100 Ω is matched to the input line of 50 Ω. In Fig. 8 we plot the broadband frequency response of the transformer. Because there is a 10 mm microstrip leading up to the transformer, the S-Parameters need to be de-embedded. This is done using “De-embed S-Parameter” under the “S-Parameter Calculations” menu on the “Post Processing” ribbon, with a distance to reference plane of -10 mm.

S-parameter plot of the quarter-wave transformer

Figure 4: Broadband S-parameter result of the quarter-wave transformer.


Note that the return is at a minimum at frequencies where the Z1 line has a length of (2n+1)λ/4, n=0,1,2,.... This can be better understood if we see the Smith Chart of the input impedance of the transformer (Fig 5). The normalized load (compared to the 50 ohm line) has a value of 2, and therefore it is the starting point of our analysis. From the load to the source we walk clockwise on a circle of constant VSWR centered at the normalized Z1(=1.41). The longer the electrical length of transforming line, the further we will walk over the constant VSWR circle. The circuit is ideally matched when the normalized impedance passes through the center of the Smith chart (the point Z=1+0i). As a complete rotation in the chart represents a half-wavelength, any integer number of 1/2λ+1/4λ will result in a matched circuit.


Smith Chart of the quarter-wave transformer from 0 – 4 GHz

Figure 5: Smith chart of the load impedance seen at the beginning of the transforming line. Note the circular pattern centered at 1.41 and passing through 1 as expected.


  • Model the same quarter-wave transformer, but make a parameter sweep in the permittivity of the substrate εr=(3.3,4.3,5.3) and observe the S-parameter results. What effect does a variation in permittivity have on the performance of the transformer? What implications does this have for the manufacturer?
  • Suppose that you have a 50 Ω microstrip line that needs to be connected, with minimum reflection at 1 GHz, to another line with 25 Ω. What impedance would be required in the quarter-wavelength transformer to match these lines? How would you expect the geometry of the new quarter-wave transformer to differ from the old one?


  • [1] D.M. Pozar, Microwave Engineering, 4th Edition, John Wiley & Sons, pp. 72-75
contact support

Your session has expired. Redirecting you to the login page...

We use cookie to operate this website, improve its usability, personalize your experience, and track visits. By continuing to use this site, you are consenting to use of cookies. You have the possibility to manage the parameters and choose whether to accept certain cookies while on the site. For more information, please read our updated privacy policy

Cookie Management

When you browse our website, cookies are enabled by default and data may be read or stored locally on your device. You can set your preferences below:

Functional cookies

These cookies enable additional functionality like saving preferences, allowing social interactions and analyzing usage for site optimization.

Advertising cookies

These cookies enable us and third parties to serve ads that are relevant to your interests.