Figure 1: E-field phase animation of a Wilkinson power divider.
Wilkinson power divider is an N-port passive device , however it is commonly found as a 2-way divider (3 ports). By manipulating the S-parameter matrix, it can be shown that it is unfeasible to achieve a 3-port device that it is at the same time:
matched in all the ports (Sii=0)
A Wilkinson power divider is a device that is matched at all ports, lossless when excited in the input port and the output ports are kept isolated. Its S-Parameter matrix for equal power division is given by Eq. 1) and its basic layout is shown in Fig. 2. In order to fully analyze this structure, one can use an "odd-even analysis" and for a complete treatment of it, please refer to 
Figure 2: Schematic diagram of Wilkinson power divider
Fig. 2 shows a schematic of a Wilkinson divider that can easily be constructed in CST STUDIO SUITE® (Fig. 3). Full dimensions are provided in the model construction notes. The model is simulated with the time domain solver in the frequency range 0 to 2 GHz.
50 Ω(Z0) line width
70.71Ω(Z0√2) line width
Length of λ/4 fo the Z0√2 line width
Figure 3: Wilkinson power divider constructed in CST STUDIO SUITE ®
In Fig. 1 we see the E-field animation when the port 1 (input) is excited. The input signal flows through the split and is divided in ports 2 and 3. Fig. 4 shows the E-field animation when port 2 is excited. Note that the signal flows through the split, but practically nothing is coupled to port 3.
Figure 4: E-field phase animation when port 2 is excited.
The S-parameters results are shown in Fig. 5. Note that ports 1, 2 and 3 are matched.
The equal power distribution can be seen by the overlapping curves of S2,1 and S3,1 and the isolation is shown by the curve S3,2.
Figure 5: S-parameters of the Wilkinson power divider
1. The isolation of the output ports is certainly an important trait of this device. Fig. 6 shows the S-parameters when port 2 is excited. As the device is matched for all ports, there is effectively no reflection in S2,2, and the isolation S3,2 tells us that no power was transmitted to the port 3, yet S1,2 shows that only approximately -3 dB was transmitted to port 1. In other words, only half of the power was transmitted. In the Physics section we gave three goals that could not be simultaneously achieved by a 3-port device. Having this in mind, take a look in the power folder of your simulation and figure out where the missing power has gone.
2. What would happen if ports 2 and 3 were excited at the same time?
Figure 6: S-parameters of the Wilkinson power divider for the excitation in port 2
 E.J. Wilkinson, "An N-way Power Divider", IRE Trans. on Microwave Theory and Techniques, vol. 8, p. 116-118, Jan. 1960, doi: 10.1109/TMTT.1960.1124668
 D.M. Pozar, Microwave Engineering, 4th Edition, John Wiley & Sons: New York, 1998, pp. 328-333
01 10 2018 article dashboard list
01 10 2018 article dashboard list
PCB Design Rules that Really Matter
Go beyond Design for Manufacturing (DFM) rule checking. This presentation introduces a smart design rule checking platform that includes knowledge of the electrical signals on modern digital PCBs. Make sure that your design can be manufactured and works.
From Layout to Multiphysics: Integrating Thermal and Photonics Simulation into the PIC Design Flow
This eSeminar will demonstrate the complete workflow to analyze thermally tuned PIC devices, starting from a component model in Luceda Photonics IPKISS.
VBA Macro for the Construction of an EM 3D Model of a Tire and Part of the Vehicle
A VBA script has been developed using CST STUDIO SUITE® tools to represent all mechanical elements in the space around the tire in a vehicle, incorporating this complex geometry in a parametric way. One of the applications of this script is the...
Simulation and Construction of Body Coil Substitute at 7T Whole Body MRI-System with Travelling Wave Concept
Magnetic resonance imaging (MRI) is one of the most important non-invasive examination methods in the modern medicine. To increase the range of medical applications, MRI systems with more powerful magnetic fields are required. Standard high-field whole...
Your session has expired. Redirecting you to the login page...
When you browse our website, cookies are enabled by default and data may be read or stored locally on your device. You can set your preferences below:
These cookies enable additional functionality like saving preferences, allowing social interactions and analyzing usage for site optimization.
These cookies enable us and third parties to serve ads that are relevant to your interests.